whew, long weekend at model-expo, #hacklabfi duties there limited my enjoyment of the fine riding weather. http://www.model-expo.com/
29.04.2012 (en)
Fried the other test board as well when raised the input voltage a bit too much at #hacklabfi, desoldered the output caps and measured them, they seem to be OK so it's either the IC or the diode that is kaputt.
rambo commented on prototype board for Micrel EL driver, uses trimmers so I can adjust the switching frequencies. (written by rambo) posted to #DIY 24.01.2012 (en)
We still have a bunch of those SMD parts (from a donation) at #hacklabfi and they're really easy to solder (though you might want to substitute other resistors if you don't have hot-air station available [though with plenty of flux those CAY16 arrays are still solderable with just an iron])
rambo commented on 3 daisy chained 595 shift-registers (from a group of 6, though they all can be separated and used individually) (written by rambo) posted to #DIY 14.10.2011 (en)
@jal Se riippuu ihan siitä millaista palikkaa olet pohtinut...
(...)
@jal Se riippuu ihan siitä millaista palikkaa olet pohtinut...
Oona saattaisi toimia mutta niitä ei vielä saa toimitukseen (mulla on ollu pre-order sisällä jo pitkään).
#hacklabfi:llä voi itse tulostella kappaleita läbin RepRap:illä (jotka ovat sen mallisia että soveltuvat FDM/FFF-tulostukseen) PLA-muovista, Shapeways:ltä saa sintrattua muovia ja metallia mutta hinta on melko paha (ne sintrausvehkeet maksaa aivan törkeästi ja on melko hitaita joten käyttöminuutille kertyy hintaa ja voittoakin pitäis saada...). Jos suunnittelee sellaisen pidikkeen joknka voi koota 2D-laserleikatuista paloista niin Formulor:iin saksassa olen ollut tyytyväinen.
Jyrsittyjen kappeleiden tekemistä voi kysellä konepajoilta mutta yleensä ovat aikalailla teollisuuden tarpeisiin orientutoneita (Aalto-yliopisto puuhaa ns fablabin perustamista mutta aikataulu taitaa olla tarpeisiisi turhan pitkä ja hinnoittelupolitiikasta ei ole tietoa)
Eikun suunnittelemaan: jos mikään 3D CADi ei ole valmiiksi hanskassa niin tarkista OpenSCAD ("The Programmers Solid 3D CAD Modeller" - me like), ideoita omaan malliin voi hakea esim Thingiversestä
Muistaakseni se "standardi" kierre joka on kameran pohjassa on jotenkin speciaali (ts. kierretapin löytäminen voi olla astetta haastavampaa) ja sintrattu metalli ei välttämättä kierteessä kestä (tarkkuuskin saattaa olla siinä ja siinä) joten se pitäis varmaan sorvata johonkin sopivan muotoseen palaan jonka sitten liimaa siihen tulosteeseen, valitettavasti en ole koskaan onnistuneesti sorvannut edes ulkokierrettä (tosin yrityksiä on vasta 2...) joten en usko että voin auttaa tämän kanssa enempää.
rambo commented on Missähän voisi teettää kunnollisen jalustaankiinnityskikkareen Samsung Galaxy SII:ta varten...? (written by jal) posted to #qaikusourcing 31.08.2011 (fi)
Here with the camera in place.
(...)
Here with the camera in place.
Also tried it on the belt (I have two units), very handy (though I need to remember that it's there when passing people in narrow spaces (like #hacklabfi hallway).
rambo commented on Finally managed to test the Capture yesterday, works great. (written by rambo) 28.08.2011 (en)
This picture is from the #hacklabfi after a day of scavenging (and photography), very handy indeed though I will be making a "belt" so that I can attach the capture unit for sideways insertion (here from top) since that way the camera frame doesn't come so close to the tightening thumbscrews (thus requiring less precise alignment to get the locking plate in).
rambo commented on Finally managed to test the Capture yesterday, works great. (written by rambo) 28.08.2011 (en)
Mulla on muuten vielä 1 buginen (address-linjat väärässä järjestyksessä, ei haittaa kun tietää ja ei tartte ketjuttaa useampaa boardia) boardi kolmelle PCA9635PW:lle, muut lahjoitin Tampereen ja Turun hacklabeille (joko harjoittelevat pintaliitosjuottamista tai tekevät niillä jotain hyödyllistä, laitoin mukaan ardu sketchin ja muut oleelliset infot), hae #hacklabfi:ltä jos haluat.
rambo commented on Pitäisi tehdä Arduinosta 3 X 1W/12V ledin pwm-ohjain. @rambo mistä kannattaa lähteä liikkeelle? (written by Ile) posted to #DIY 10.08.2011 (fi)
I plan on using this with 2S lipo battery to power the "UFO project", Jaroneko from #hacklabfi tested that the regulator cut-off (it of course requires a bit more than 5V to input to work) is handily at around the voltage under which a 2S battery should not go, so there is a battery protection circuit for free.
rambo commented on board for DX 5V step-down regulator (written by rambo) posted to #DIY 10.07.2011 (en)
rambo commented on Pitäisi tehdä Arduinosta 3 X 1W/12V ledin pwm-ohjain. @rambo mistä kannattaa lähteä liikkeelle? (written by Ile) posted to #DIY 05.07.2011 (fi)
| Tools | |
| #hacklabfi rss | |
Qaiku channel for Helsinki Hacklab, a hackerspace in Helsinki. Closely related with #DIY.
This channel is for everybody
Copyright Rohea Oy 2010 | Mobile version | Feedback | API | Terms of Service | Applications and tools